Ruger M77 MK II Bolt disassembly

This is a discussion on Ruger M77 MK II Bolt disassembly within the DIY forums, part of the Sniping Related category; Hi all, I am re-barrelling my M77MkII VT and want to get the barrelled action teflon coated once completed. I need to be disassemble the ...

Results 1 to 4 of 4
  1. #1
    Junior Member
    Join Date
    Nov 2005
    Location
    Australia
    Posts
    7

    Ruger M77 MK II Bolt disassembly

    Hi all,

    I am re-barrelling my M77MkII VT and want to get the barrelled action teflon coated once completed.

    I need to be disassemble the bolt (remove the firing pin assembly to allow for coating of the sleeve and cocking piece). Looking in the owners manual, it refers to inserting a pin into a 'disassembly hole'

    Quite frankly, the instructions provided by Ruger are less than adequate. Does anyone have any pics or suggestions on how I can do this??

    Any help would be much appreciated!!
    Cheers,

    BigDaddy

  2. #2
    Senior Member
    Join Date
    Jun 2004
    Location
    Midland, TX
    Posts
    192
    Heres the schematic for a ruger M77 Mk II from brownells, maybe it will help out a little.

    http://www.brownells.com/aspx/NS/sch...K+II+Standard+
    If you're not living on the edge, you're taking up too much room.

  3. #3
    Junior Member
    Join Date
    Nov 2005
    Location
    Australia
    Posts
    7
    Thanks 6.5

    this job is proving to be a right PITA :x
    Cheers,

    BigDaddy

  4. #4
    Junior Member
    Join Date
    Nov 2005
    Location
    Australia
    Posts
    7
    Ive managed to get the job done.

    For any who r interested, u need to have te bolt cocked and pass a pin thru a hole in the cocking piece. What they dont tell u is where the hole is as there are 3 holes.

    What they also dont tell u is that u need to pull back on the bolt to get a pin thru the hole as part of it is obscured by the cocking indicator. U do this using an edge of a bench whilst using your other 4 hands to insert a the pin.

    Once this is done, u can remove the shroud and firing pin assy from the bolt. Dont get me started on the extractor ring though :roll: That being said, the whole job was a PITA (and it was a practice run whilst I'm waiting on the new barrel!!) but a necessary evil seing I am getting the thing teflon coated.

    Give me my remington any day!!!
    Cheers,

    BigDaddy

Ads

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Surgeon bolt disassembly ..... ?
    By Kiwi in forum Rifles
    Replies: 3
    Last Post: 05-10-2011, 08:23 PM
  2. 700 Bolt/Pin Disassembly
    By XMahkaihX in forum Rifles
    Replies: 2
    Last Post: 02-17-2011, 10:50 AM
  3. Ruger 77/44 suppressed with Tac Ops bolt knob
    By 45cal4life in forum Gallery
    Replies: 3
    Last Post: 03-11-2009, 06:07 PM
  4. Savage 110fp bolt disassembly
    By TONKA TOY in forum Rifles
    Replies: 3
    Last Post: 05-02-2007, 09:02 AM
  5. Bolt Disassembly/Cleaning
    By NiceDay2 in forum Off Topic
    Replies: 10
    Last Post: 04-29-2007, 12:44 PM

Search tags for this page

how to disassemble a ruger m77 mark ii bolt
,
m77 bolt disassembly
,
removing the firing pin assembly from a ruger 77
,

ruger m77 bolt diagram

,

ruger m77 bolt disassembly

,

ruger m77 mark ii bolt disassembly

,
ruger mark ii bolt disassembly
,
ruger mkii bolt disassembly
Click on a term to search for related topics.