12GA FH- Hairy Blaster- - Page 2

12GA FH- Hairy Blaster-

This is a discussion on 12GA FH- Hairy Blaster- within the DIY forums, part of the Sniping Related category; Here is picture of a neat scaled up Sharps replica that would handle out 12GA FH and my 700HE. That outside hammer looks great. From ...

Page 2 of 32 FirstFirst 123412 ... LastLast
Results 11 to 20 of 319
  1. #11
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here is picture of a neat scaled up Sharps replica
    that would handle out 12GA FH and my 700HE.
    That outside hammer looks great. From a magazine
    article in Very High Power...Ed

    Ed Hubel

  2. #12
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here are some of the variety of slugs pictured,
    that we have tested. Ed



    Ed Hubel

  3. #13
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here is picture of a dart type 12ga slug Rob made. Body
    is aluminum, it has a heavy tungsten carbide insert in the
    nose. The TC in the nose is about 5 times denser than AL.
    Total length is 2.35 inches, weight about 950 gr. The .75" long
    insert a real tight type fit. Heat AL, put in insert, cools, locks on.
    It is fairly streamlined, yet has wide meplat for penetration
    in game. Flat points penetrate straighter in game.
    It is hollow inside in the back, behind insert which puts the
    center of gravity way up front, it should fly straight even from
    a smoothbore. They are fast to make and material
    less expense than copper.In pic is a copper and a brass 600
    cal slugs for comparison. Dart/slug on right has insert.Ed

    Ed Hubel

  4. Remove Advertisements
    SniperForums.com
    Advertisements
     

  5. #14
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here are more samples of nice 12ga slugs.....Here is pic of
    ones RG Henson sent. Jacketed 12ga. 715gr hollowpoints,
    on the right and in front a jkt 675gr hollowbase.
    RG's number 1-770-366-4846. These will be great for
    shorter plastic and brass cases as well as long cases.
    Other slugs in pic, in the back, left to right
    Foster 436gr- Dixie 600gr- 750gr brass- my 750gr hollowbase
    brass, and a hollowpoint I put a lightweight filler in the nose
    for streamlining..Ed

    Ed Hubel

  6. #15

    Join Date
    Jan 2008
    Posts
    299
    stupid question here, but with that much BOOM... does it quater the game for you on impact?? i am not a huge game hunter, but this seems to be a little much even for an Elk? what game is it intended for and at what distance? i imagine with that dart system you can hit 200yds fairly easy.

    i would hate to be behind that thing :cry: what does it feel like compare to say a .50 cal BMG? Cause i honestly dislike shooting slugs from my Benelli M4 adn that thing is a pussy cat, comparied to this Saber tooth tiger

  7. #16
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    It is for fun and putting big holes in stuff.
    My Savage is heavy, and full loads are like a 12ga
    8lb gun with super magnum loads.Many big game
    hunters are limited to shotguns, and we are helping
    them to get more power than rifles at moderate
    to short ranges.Ed
    Ed Hubel

  8. #17
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here is picture of our case sectioned next to a
    thin factory brass case to show the great strength.
    And our case in pic was fired 35 times and shows
    no stretching. Ed

    Ed Hubel

  9. #18
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Testing 715gr jacketed hollowpoint from RG Henson in Savage 210.
    With 30 inch barrel, long brass 3.85" case, big primer.
    Slightly hairy load 290gr RL22--2700 fps. Shot moderate load
    of 300gr W-860 -- 2400 fps for 3 shot group of 3" at 50
    yards with my bad eyes and peep sights. They shoot nice, they go
    into target straight.. Other nice thing the price from RG,
    for customers getting in on his first run, $1.25 plus shipping.
    That is less than half of what other big bore jkt bullets cost.
    Call him for some great slugs. They are great like
    the Dixie slugs. Ed
    Ed Hubel

  10. #19
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Lookee what another santa sent me.
    A regular BMG case on the left, and
    a straight BMG case on the right, and it
    CAME FROM THE MANUFACTURER THAT WAY.

    It is primer cartridge for large guns and howitzers.
    It is used in those guns/cannons that have powder in big bags.
    It is filled with powder and inserted into cannon breach and
    when fired sets off the larger charge. On some cannon breaches
    they have an automatic feed for these with a huge 40 round
    drum magazine. This on is marked IVI 89 C67. IVI is Canadian.
    On these breaches it is held by collet fingers for head space
    and for ejection.

    Ok, there are many thousands more of these out there than the
    PROP cases I showed before. We need to find few barrels of these
    and have Rob, etal, put on rims.... no annealing.....no fireforming,
    just slight resize to 12GA FH. Please help if you know of any.
    They would save so much work and time..And even though fired
    the bases are perfectly straight, another plus.....Ed

    Ed Hubel

  11. #20
    Senior Member
    Join Date
    Jul 2008
    Location
    Brinton, MI
    Posts
    367
    Here is a picture of RG's jacketed 715gr slugs in various
    loads.First are 2.75" and 3" factory foster slugs\ for
    comparison. 3rd is jkt HP in 3.5" plastic case, 4th in a
    3" brass RMC case. 5th in a 3.5" brass case with small
    primer, 6th in our long brass 3.85" case, big primer.
    Top hairy load in long case in Savage, 2900..Ed

    Ed Hubel

Page 2 of 32 FirstFirst 123412 ... LastLast

Ads

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. Team Blaster at SHOT
    By Rob01 in forum Misc.
    Replies: 1
    Last Post: 01-17-2010, 08:10 AM
  2. Spiders in my 12ga
    By theloss52 in forum Off Topic
    Replies: 4
    Last Post: 03-20-2009, 05:25 AM
  3. Beretta 12ga. chokes and wrench- who needs them?
    By perpetual motion in forum Rifles
    Replies: 3
    Last Post: 02-27-2009, 02:41 PM
  4. 204 Pdog blaster done...
    By 7mmRM in forum Gallery
    Replies: 21
    Last Post: 02-29-2008, 06:11 AM

Search tags for this page

12 ga. fh

,

12 ga. fh 3 3 1/2 in

,

12 gauge fh

,
12 gauge slug mold
,

12ga fh

,

diy 12ga fh

,

diy primer shotgun

,
ed hubel
,

homemade 12 gauge roll crimp

,

homemade 12 gauge roll crimp tool

,

news

,

slug wads

Click on a term to search for related topics.